Eng | 简体 | 繁體
My favorites
-> -> -> - >
[Sell Offer]The following message about repair was posted by cntestbench
Visit:7 ,Today:1

How To Repair Denso Common Rail Injector-3

Solenoid assembly
Resistance checks should be made to the solenoid. The specific resistance measured will depend upon the type of injector and should be compared to a new unit. The resistance recorded on the particular G2 injectors that we tested was approximately 0.5 -0.7 Ohms.

Obvious signs of any damage to the outer casing or splits/cracks on the electrical connector should be observed. Check for erosion/corrosion of the electrical terminals and ensure that the inner surface of the solenoid is clean and free from dents etc (Fig13).

Ensure that the solenoid spring is in good condition. It may be a good idea to check and record the length against a new one.

Solenoid Valve and Half Ball Valve assembly
Check the condition of the solenoid valve assembly , paying particular attention to the half ball valve face and the seat inside the valve stem. The flat face of the half ball valve is responsible for sealing the control chamber, so it must be in good condition with no erosion or wear. These components are best inspected under a microscope. Check the conical seat that the ball seats on inside the valve, as well as the valve stem for any signs of wear, scratches and erosion (Fig 14)

Renew both components if there are any abnormalities or doubt on their condition (both available from Diesel Distributors).

Valve Seat and Retaining Nut

Inspect the valve seat for erosion and wear (Fig 16). As with the ball and valve assembly, this is probably best viewed under a microscope or other magnification equipment. If there are any marks across the seating area that would suggest a sealing problem-renew the valve seat (available through Diesel Distributors).

Inspect the sealing face of the retaining nut for signs of erosion and wear (Fig 16).

Due to the very fine tolerances involved in CR injectors, lapping of the sealing surfaces of these components is not recommended. Any attempt to lap the surfaces should be undertaken with the utmost care and with the use of VERY FINE lapping pastes.

Command Piston & Injector Body
Check the piston for scoring and wear marks along with the inner bore of the injector. If there is considered to be excessive scoring or wear on either component, then the unit will more than likely be scrapped (Fig 17). The piston should be clean, free from scoring and move freely inside the injector bore with no ‘snagging’ or tight spots.

Nozzle Assembly, Pressure Spindle and Spring.
Guidelines for inspecting the nozzle assembly can be considered the same as for any conventional nozzle. Check for excessive wear or scoring on the needle shank and seat and renew the nozzle if necessary. (Genuine and non-genuine nozzles are available from Diesel Distributors, depending upon application and availability). Check the spring for condition and the spindle for excessive wear on the spring seat.

When re-assembling any common rail components, clean practices should always be observed and the utmost precaution should be taken to avoid any contamination of the components before and during assembly.


Last modified: 2020-10-10 17:09:35
  • Report this Ad - Welcome to Make a Pubilc Comment : How To Repair Denso Common Rail Injector-3

    * Required information

    Excellent Wrong Category Prohibited Contents Spam Outdated Other

    Full Name: *
    Message: *

Related seek: Filters - Industrial Supplies Agents - Animal Husbandry Equipment - Cable & Wire - Insulating Materials - Industrial Batteries - Energy Saving - Daily Products Machinery - Second Hand Equipment - Industrial Supplies Stocks - Refrigeration Heat Exchange - Hardware Tools - Standard Parts - Metallic Processing Machinery - Electronic Data Systems - Industrial Supplies - Farm Machines Tools - Oil Seal & Ring - Abrasives - Printing Machinery - Electric - Others - Food Processing Machinery - Packaging Related Machinery - Mining Machinery - Electric Control & Protect - Forest Machinery - Industrial Supplies Projects - Fishery Machinery - Draught Fan

©2021 Swkong.com